Ka UV Airy Moist Soft Serum SPF 50+ Versus L'Oreal UV Defender UV Serum Protector Sunscreen SPF 50+

Because it is not a free-fatty acid, this ingredient is fungal acne safe (there's nothing for Malassezia to feed on).

A high amount of carbomer can cause pilling or balling up of products. Don't worry, most products contain 1% or less of carbomer.

Dimethicone comes in different viscosities:

Depending on the viscosity, dimethicone has different properties.

Ingredients lists don't always show which type is used, so we recommend reaching out to the brand if you have questions about the viscosity.

This ingredient is unlikely to cause irritation because it does not get absorbed into skin. However, people with silicone allergies should be careful about using this ingredient.

Note: Dimethicone may contribute to pilling. This is because it is not oil or water soluble, so pilling may occur when layered with products. When mixed with heavy oils in a formula, the outcome is also quite greasy.

You'll often see it paired with other UV filters to boost overall SPF because octisalate is a fairly week filter on its own.

The reason you'll see it so often is because it can help solubilize and stabilize the trickier filters like oxybenzone and avobenzone.

Unlike these filters, octisalate has pretty good photostability and doesn't create skin-damaging free radicals when exposed to sunlight.

The fatty-alcohol part of the molecule also gives it a light, emollient feel so it doubles as a nice texture enhancer.

Usage levels vary around the world:

Safety-wise, this ingredient has a pretty reassuring track record. The EU's Scientific Committee on Consumer Products (SCCP) found very low skin penetration in human skin tests and negative results for irritation, phototoxicity, and photoallergy.

The real-world allergy risk is pretty low too; a 2012 European study of 1,031 people recorded only 2 reactions to it (a rate of 0.19%).

You might have seen scary headlines about sunscreen getting into your blood.

In 2019, the FDA found that several chemical filters can absorb through the skin and show up in the bloodstream at small but measurable levels.

Here's the important part: these tiny levels are just a cutoff the FDA uses to decide which ingredients need more testing and doesn't mean anything harmful was found.

The researchers were clear that the results are no reason to stop wearing sunscreen.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

Because hydrolyzed hyaluronic acid is smaller in size, it can slip past your outermost layer of skin more easily than full-sized HA.

Most formulations will combine all sizes to get the best of both worlds.

Typical usage levels range from 0.01-1%. Any percentage higher than 2% might become goopy and tacky.

Tinosorb M covers a range of 280-400 nm and is photostable. This ingredient is neither oil or water soluble.

Tinosorb M is not available in the US. However, it is available in the EU and Asia.

It's sister, Tinosorb S, is set to be approved in the US by late 2025 (fingers crossed!).

Propanediol is not likely to cause sensitivity and considered safe to use. It is derived from corn or petroleum with a clear color and no scent.

The unique structure of silica enhances the spreadability and adds smoothness, making it a great texture enhancer.

It is also used as an active carrier, emulsifier, and mattifier due to its ability to absorb excess oil.

In some products, tiny microneedles called spicules are made from silica or hydrolyzed sponge. When you rub them in, they lightly polish away dead skin layers and enhance the penetration of active ingredients.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!