StriVectin Advanced Retinol Nightly Renewal Moisturizer Versus Neutrogena Rapid Wrinkle Retinol Regenerating Cream

Typical use ranges from 0.5-30%. Most leave-on products are in the 1-10% zone.

The 20 ethylene oxide units is well above the PEG-10 threshold and therefore not a food source for Malassezia (it's fungal acne safe).

This ingredient has a comedogenic rating of 2 and an irritancy rating of 3. These numbers come from testing the raw ingredient on rabbit ears and doesn't reflect how it will behave in a finished product.

In practice, this ingredient is a well-tolerated ingredient. The ratings reflect cautious lab conditions and not real-world use. Just be sure to patch test any formulas you feel unsure about.

It plays several roles in a formula:

Typical use levels for this ingredient sit around 1-10% and the Cosmetic Ingredient Review Expert Panel has affirmed safety at concentrations up to 25% in leave-on products.

Multiple assessments have found it to be non-irritating and non-sensitizing to most people.

However, there have been some cases of allergic contact dermatitis in patients with chronically compromised skin barriers.

Cetearyl alcohol has a comedogenic rating of 2 and irritancy rating of 1. Both of these numbers come from the 1989 study that used rabbit ears; a "2" means mildly comedogenic and a "1" means low irritancy.

Here's the catch: rabbit skin is more sensitive than human skin and throws a lot of false positives. A 1996 reappraisal found that ingredients rated 1-2 in the rabbit ear tests are generally safe for humans.

Remember comedogenic ratings are unable to assess the entire formula of a product or how it will react on your skin. Just be sure to patch test if you are unsure about certain ingredients.

This ingredient is not fungal acne safe. Cetearyl alcohol is a fatty alcohol with chain lengths that fall within the range that Malassezia can metabolize.

A 2019 study has also observed Malassezia growth in the presence of this ingredient, confirming it to be not-fungal acne safe.

Dimethicone comes in different viscosities:

Depending on the viscosity, dimethicone has different properties.

Ingredients lists don't always show which type is used, so we recommend reaching out to the brand if you have questions about the viscosity.

This ingredient is unlikely to cause irritation because it does not get absorbed into skin. However, people with silicone allergies should be careful about using this ingredient.

Note: Dimethicone may contribute to pilling. This is because it is not oil or water soluble, so pilling may occur when layered with products. When mixed with heavy oils in a formula, the outcome is also quite greasy.

On top of that, this ingredient can counteract the effects of hard water by binding to the minerals in it.

One thing worth knowing is that Disodium EDTA has been shown to be a mild penetration enhancer. It can help other ingredients absorb into skin more effectively which can be a double-edged sword (great for actives, but can also make the active too strong if you have sensitive skin).

Clinical patch testing showed no significant skin irritation at typical use concentrations and minimal dermal absorption.

You'll most likely see this ingredient near the end of an ingredient list. It's typically found in concentrations less than 1%.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

Isohexadecane is often used in products designed to help oily skin. It is lightweight and non-greasy while helping to moisturize. When mixed with silicones, it gives a product a silky feel.

On a cellular level, it disrupts the cell membranes of microbes by poking holes that make the cell leak. This shuts down the chemical reactions the microbe needs to make energy so it can no longer survive.

Another perk of this ingredient is that it stays functional across a wide pH range (3-10).

You'll often see it paired with boosters like Ethylhexylglycerin; one study showed that a 1:9 ratio of Ethylhexylglycerin to Phenoxyethanol damages bacterial membranes as effectively as doubling the Phenoxyethanol concentration on its own.

Typical use concentrations range from 0.3-1% depending on the formula, and this ingredient is capped at 1% int the EU.

Safety-wise, the fear mongering does not hold up to the evidence. The EU's Scientific Committee on Consumer Safety and FDA consider it safe as a preservative at up to 1%, including for children of all ages.

Adverse systemic effects only showed up in animal studies at exposures roughly 200x higher than what people get from cosmetics. And despite its very widespread use, this ingredient is a rare sensitizer and allergic reactions are uncommon.

The common safety discussion around this ingredient involves a manufacturing byproduct called 1,4-dioxane.

Trace amounts can form during production but the EU's Scientific Committee on Consumer Safety has concluded that levels at/below 10 ppm in finished products are safe (commercial products consistently fall within acceptable margins).

True allergic reactions are uncommon and the CIR Expert Panel has confirmed this ingredient to be safe as used in cosmetics.

Because it is derived from lauric acid, it may not be fungal acne safe.

Once converted, it binds to receptors that switch on genes controlling how skin cells behave. In practice, this means a few things happen in a formula. It:

The research backs this up as well.

A pooled analysis of six clinical studies found that 0.1% stabilized retinol improved signs of photoaging as early as week 4 and through 12 weeks without causing major irritation.

Another study comparing concentrations found that 0.1 and 0.3% retinol were similarly effective at remodeling photodamaged skin, but 0.3% was associated with fewer adverse reactions when used daily (a useful reminder that more isn't always better).

Retinol is about tenfold less potent than Retinoic Acid which is why it works as a gentler, non-prescription option that builds results over time.

Typical concentrations range from 0.1-1%, with 0.1% to 0.3% being a well-supported sweet spot for visible benefits with good tolerability.

The most common side effects are mild and temporary: usually some dryness, redness, or light peeling as your skin adjusts. These tend to settle with consistent and lower-frequency use.

Like all retinoids, retinol works best with nightly use, a good moisturizer, and daytime sunscreen.

The "ramp up" method works well: start with Retinol once a week to give your skin time to adjust, which keeps irritation low.

Slowly add more nights until you reach your goal frequency once your skin feels comfortable.

Retinoids also make your skin more sensitive to the sun in the first few weeks, so wear sunscreen every morning and protect your skin from direct sun while you build up tolerance.

Interestingly, the size of the molecule affects its behavior:

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

Many serums use a blend of both weights so you can get surface hydration plus longer-lasting and deeper effects.

You'll typically see concentrations between 0.1-2% for this ingredient.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!