Luxe Organix 6 In 1 Maxshield Active Ultra Sheer Face And Body Sunscreen SPF 150 Versus SKIN1004 Madagascar Centella Hyalu-Cica Water-Fit Sun Serum SPF50+ PA++++

Because it has a neutral charge, it is compatible with a wide range of ingredients and stays stable across a broad pH range/water hardiness conditions.

Patch testing has shown it to have the lowest irritation potential among common cleansing surfactants (like SLS).

Typical use levels range from 5-20% in rinse-off cleansers.

One thing worth knowing: The American Contact Dermatitis Society named the parent family, alkyl glucosides, "Allergen of the Year" in 2017. The prevalence of allergy is pretty low but be sure to patch test if you've reacted to "gentle" or sulfate-free cleansers before.

This ingredient is fungal acne safe because the fatty alcohol portion of this ingredient is not within the C11-24 chain length that Malassezia can metabolize.

This ingredient has been found to be safe as used in cosmetics, wasn't a skin or eye irritant in clinical patch testing, and wasn't phototoxic.

In a clinical comedogenicity test, this ingredient tested negative so it isn't likely to clog pores.

Typical use levels are about 5-8% for sunscreens + nail products, but can range from 0.005%-8% depending on the product.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

The only catch is that HA isn't a single thing; it actually comes in a wide range of molecular weights (~50 - 2,000+ kDA) and size matters.

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

This is why the best HA serums blend the two sizes together so you get the best of both worlds.

The majority of cosmetic HA is produced by bacterial fermentation, typically using Streptococcus or Bacillus strains. Typical use levels in skincare sit around 0.1-2%.

A clinical study using a 0.2% low-molecular weight HA gel showed improvement in facial seborrheic dermatitis with excellent tolerance.

These are some other common types of Hyaluronic Acid:

Because hydrolyzed hyaluronic acid is smaller in size, it can slip past your outermost layer of skin more easily than full-sized HA.

Most formulations will combine all sizes to get the best of both worlds.

Typical usage levels range from 0.01-1%. Any percentage higher than 2% might become goopy and tacky.

One of its best party tricks is photostability; it doesn't break down with repeated sun exposure and doesn't generate free radicals in the process either. You'll also see it paired with wobbly filters like avobenzone because it helps stabilize them.

The safety profile is assuring as well. Because it's a large molecule, it doesn't easily absorb into skin and rarely causes irritation.

It's approved in the EU, Asia, and Australia up to 10% and most formulas land somewhere in the 2-10% range.

You won't find it as a sunscreen active in the US, but it can make an appearance as a formula-protecting UV-absorber.

On the safety side, the Cosmetic Ingredient Review Expert Panel has concluded this ingredient to be safe as used in current cosmetic practices + concentrations.

Typical use levels in a formula run about 1-5%.

Typical use levels sit around 0.1-3%, with 0.3-3% more common in leave-on emulsions.

This ingredient was reviewed as part of a group of 126 acrylates and concluded to be safe by the Cosmetic Ingredient Review Expert Panel.

Though acrylate contact allergy is real and well-documented, allergy risk is quite low. The cases of documented contact allergy are caused by unreacted monomers (more commonly found in gel nails, dental resins, and adhesives).

One manufacturer claims this ingredient to have a pH range of 2-8 and to be biodegradable.

This ingredient is also known as Sepimax Zen.

Interestingly, the size of the molecule affects its behavior:

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

Many serums use a blend of both weights so you can get surface hydration plus longer-lasting and deeper effects.

You'll typically see concentrations between 0.1-2% for this ingredient.

Topically applied tocopherol has been shown to protect against UV damage by ramping up the skin's own natural defense enzymes.

It also acts as a skin conditioning agent; some studies show that regular topical use can improve the skin's water-binding capacity over 2-4 weeks.

This ingredient is especially loved for being a team player. When combined with Vitamin C, the photoprotective effect of both ingredients roughly doubles and the combo also helps reduce UV-induced DNA damage.

This ingredient has some brightening potential but it's more of a prevention ingredient than spot-fader. Cell studies show it can slow down melanin production but it's worth noting that it's not the most powerful brightener out there.

In formulations, it also serves as a stabilizer that helps protect other oxidation-prone ingredients from degrading.

Concentrations usually range from 0.1-1% in most leave-on products.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!

Xanthan gum is a pretty common and great ingredient. It is a natural, non-toxic, non-irritating ingredient that is also commonly used in food products.