TheSkinlist Advanced Biogf Peptide Youth Serum Versus Nectapharma Alchemi Wrinkle Expert M3 Peptide Serum

A high amount of carbomer can cause pilling or balling up of products. Don't worry, most products contain 1% or less of carbomer.

On top of that, this ingredient can counteract the effects of hard water by binding to the minerals in it.

One thing worth knowing is that Disodium EDTA has been shown to be a mild penetration enhancer. It can help other ingredients absorb into skin more effectively which can be a double-edged sword (great for actives, but can also make the active too strong if you have sensitive skin).

Clinical patch testing showed no significant skin irritation at typical use concentrations and minimal dermal absorption.

You'll most likely see this ingredient near the end of an ingredient list. It's typically found in concentrations less than 1%.

Industry-reported use ranges from 8% in rinse-off products and 2% in leave-on formulations.

It's worth knowing sugars are already a natural component of the skin's NMF (natural moisturizing factor) so it's a molecule that your stratum corneum is well-acquainted with.

Just so you know, glucose is hydrophilic (water-loving) and the stratum corneum is a strong barrier to hydrophilic compounds. This just means penetration is slow and most of the action is happening on the surface.

Gram-to-gram, glucose is not as efficient as a humectant as glycerin. This is why you'll likely see glycose paired with stronger humectants for a bigger hydration payoff.

In skincare, glucose is typically derived from corn or other starch sources.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

This ingredient calms down a specific inflammation signal in your skin cells (called IL-6). When left unchecked, this signal triggers enzymes that break down collagen and elastin.

Clinical testing showed statistically significant improvements in:

Studies also found the more of this ingredient used, the more your skin produces Collagen I, fibronectin, and hyaluronic acid.

You'll likely see this ingredient paired with Palmitoyl Tripeptide-1 in the well-known Matrixyl 3000 complex for enhanced anti-aging effects.

A 3% concentration applied twice daily for two months showed meaningful skin rejuvenation results in clinical panels.

Fungal acne note:
Usually a palmitic acid component can feed Malassezia in unbound form, but here is is covalently bonded to the peptide. This means it is very difficult for Malassezia to access, and therefore very unlikely to cause fungal acne.

Once there, it acts as a matrikine, a signaling peptide that prompts fibroblasts to produce more collagen, fibronectin, and hyaluronic acid.

In vitro studies show it can boost collagen production in skin cells even when UV-damaged skin samples were treated with it at a tiny concentration (it almost fully restored dermal collagen at 5ppm). It achieved this at 100x lower concentration than retinoic acid, which needed 500 ppm to do the same thing.

Human clinical data is promising, but modest:

A study of 23 female volunteers found a small but statistically significant increase (~4%) in skin thickness after treatment at 4 ppm.

A separate small trial of 15 women showed statistically significant reductions in wrinkle length, depth, and skin roughness after applying it twice daily for four weeks.

You'll likely see Pal-GHK paired with Palmitoyl Tetrapeptide-7 as part of the Matrixyl 3000 complex.

Fungal acne note:
Usually a palmitic acid component can feed Malassezia in unbound form, but here is is covalently bonded to the peptide. This means it is very difficult for Malassezia to access, and therefore very unlikely to cause fungal acne.

The common safety discussion around this ingredient involves a manufacturing byproduct called 1,4-dioxane.

Trace amounts can form during production but the EU's Scientific Committee on Consumer Safety has concluded that levels at/below 10 ppm in finished products are safe (commercial products consistently fall within acceptable margins).

True allergic reactions are uncommon and the CIR Expert Panel has confirmed this ingredient to be safe as used in cosmetics.

Because it is derived from lauric acid, it may not be fungal acne safe.

Interestingly, the size of the molecule affects its behavior:

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

Many serums use a blend of both weights so you can get surface hydration plus longer-lasting and deeper effects.

You'll typically see concentrations between 0.1-2% for this ingredient.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!