SCINIC Enjoy Super Mild Sun Essence SPF50+ PA++++ Versus Skin Aqua UV Brightening Moisture Gel SPF 50

Because it has a neutral charge, it is compatible with a wide range of ingredients and stays stable across a broad pH range/water hardiness conditions.

Patch testing has shown it to have the lowest irritation potential among common cleansing surfactants (like SLS).

Typical use levels range from 5-20% in rinse-off cleansers.

One thing worth knowing: The American Contact Dermatitis Society named the parent family, alkyl glucosides, "Allergen of the Year" in 2017. The prevalence of allergy is pretty low but be sure to patch test if you've reacted to "gentle" or sulfate-free cleansers before.

This ingredient is fungal acne safe because the fatty alcohol portion of this ingredient is not within the C11-24 chain length that Malassezia can metabolize.

DHHB has been approved by the EU, Japan, Taiwan, and South America for use up to 10%. Unfortunately, it has not been approved for use in the US or Canada due to slow regulatory processes.

This ingredient is soluble in oils, fats, and lipids.

Two of its biggest selling points are efficiency and stability:

Most of the other chemical filters are considered "photostable" if they can last for two hours.

Because this ingredient is oil-loving, it can sit neatly into the oil phase of emulsions and shines in water-repellent/water-resistant formulations.

The EU and Canada allow it to be used up to 10% and Japan allows it up to 5%.

Unfortunately, it's not yet an FDA approved sunscreen agent so you won't be able to find it in sunscreens in the US.

Safety-wise, it has a pretty solid record: the EU's Scientific Committee on Consumer Safety (SCCS) has reviewed it and found low skin absorption, no capacity to produce skin irritation or photo-irritation.

In vitro testing has found less than 0.1% of the applied dose is absorbed by the skin over 24 hours (mostly due to its large molecule size).

Fun fact: This ingredient even has anti-inflammatory properties similar to those of ketoprofe, an anti-inflammatory medication.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

Tinosorb M covers a range of 280-400 nm and is photostable. This ingredient is neither oil or water soluble.

Tinosorb M is not available in the US. However, it is available in the EU and Asia.

It's sister, Tinosorb S, is set to be approved in the US by late 2025 (fingers crossed!).

Polymethylsilsesquioxane has not been shown to clog pores. It has been deemed safe to use up to 55%, but most cosmetics use much less.

If you have concerns about using this ingredient, we recommend speaking with a professional.

The unique structure of silica enhances the spreadability and adds smoothness, making it a great texture enhancer.

It is also used as an active carrier, emulsifier, and mattifier due to its ability to absorb excess oil.

In some products, tiny microneedles called spicules are made from silica or hydrolyzed sponge. When you rub them in, they lightly polish away dead skin layers and enhance the penetration of active ingredients.

Interestingly, the size of the molecule affects its behavior:

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

Many serums use a blend of both weights so you can get surface hydration plus longer-lasting and deeper effects.

You'll typically see concentrations between 0.1-2% for this ingredient.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!

Xanthan gum is a pretty common and great ingredient. It is a natural, non-toxic, non-irritating ingredient that is also commonly used in food products.