What's inside

What's inside

Key Ingredients

Benefits

Concerns

Ingredients Side-by-side

Show highlights for:

Reviews

No reviews yet

Be the first to review

Write the first review
4.07
Overall rating
5
4
3
2
1
What people say
Works Well 57% Great Value 43% No Scent 35%

Ingredients Explained

These ingredients are found in both products.

Ingredients higher up in an ingredient list are typically present in a larger amount.

Emollient, Humectant, Skin Conditioning

Caprylyl Glycol is a humectant, skin conditioner, emollient, and preservative booster derived from either caprylic acid or synthetically created.

Typical use levels vary from 0.3-1% as a preservative booster and go up to 2% to condition skin.

Because it is not a free-fatty acid, this ingredient is fungal acne safe (there's nothing for Malassezia to feed on).

Learn more about Caprylyl Glycol

Dimethyl Isosorbide (often shortened to DMI) is a sugar-derived solvent made from sorbitol. It's used to dissolve tricky ingredients and help them mix smoothly into a formula.

Many actives sit as gritty crystals when undissolved, so DMI swoops in to full dissolve them. This helps improve texture, stability, and how evenly an active is distributed.

It does have a penetration-enhancing reputation that is a bit more nuanced than marketing suggests; a cell study on human skin found that 10% DMI didn't significantly boost the permeation of Hydroquinone, Salicylic Acid, or Octadecenedioic Acid compared to controls (though it did improve their solubility in the formula itself).

Typical usage concentrations usually range from 1-10% depending on the formula's needs; this ingredient is also well tolerated at these levels.

Learn more about Dimethyl Isosorbide
Skin Conditioning, Solvent

Pentylene Glycol (1,2-pentanediol) is a multitasking little diol with three main roles in a formula:

Research on alkanediols (the family pentylene glycol belongs to) show they work by disrupting microbial cell membranes. This disruption helps the primary preservative system in a product work more effectively at lower doses.

On the safety side, the Cosmetic Ingredient Review Expert Panel has concluded this ingredient to be safe as used in current cosmetic practices + concentrations.

Typical use levels in a formula run about 1-5%.

Learn more about Pentylene Glycol
Emulsifying, Surfactant

Polysorbate 20 is a gentle, water-soluble emulsifier and mild surfactant. It stops oil and water from separating to keep your formulas blended and stable.

It also acts as a mild penetration enhancer by helping active ingredients absorb slightly better.

The common safety discussion around this ingredient involves a manufacturing byproduct called 1,4-dioxane.

Trace amounts can form during production but the EU's Scientific Committee on Consumer Safety has concluded that levels at/below 10 ppm in finished products are safe (commercial products consistently fall within acceptable margins).

True allergic reactions are uncommon and the CIR Expert Panel has confirmed this ingredient to be safe as used in cosmetics.

Because it is derived from lauric acid, it may not be fungal acne safe.

Learn more about Polysorbate 20
Humectant, Skin Conditioning

Sodium Hyaluronate Crosspolymer is a crosslinked version of sodium hyaluronate. This just means it's linked into a 3D mesh network that lets it be more stable and sit on skin as a cohesive, gel-like film rather than sinking into skin.

A 2016 human skin study found crosslinked HA increased epidermal water content by 7.6% over the control group and reduced transepidermal water loss by 27.8%.

A follow-up clinical trial found that a topical crosslinked HA serum applied after fillers, microneedling, or chemical peels was well-tolerated and enhanced skin quality at 14 / 28 days.

More recent research suggests that concentrations as low as 0.03% can act as a penetration enhancer for other skincare actives.

Learn more about Sodium Hyaluronate Crosspolymer

Similar Comparisons