Dr.Ceuracle Pro Balance Comfort Sun Stick SPF 50+ Versus B.LAB Matcha Hydrating Real Sun Stick SPF 50+

Butyloctyl Salicylate is a chemical UV filter structurally similar to octisalate. It is a photostabilizer, SPF booster, emollient and solvent. This ingredient helps evenly spread out ingredients.

According to a manufacturer, it is suitable for pairing with micro Titanium Dioxide, Zinc Oxide, and pigments.

Caprylyl Glycol is a humectant, skin conditioner, emollient, and preservative booster derived from either caprylic acid or synthetically created.

Typical use levels vary from 0.3-1% as a preservative booster and go up to 2% to condition skin.

Dibutyl Adipate is a lightweight, oil-soluble ester that acts as an emollient and solvent. It helps products spread more easily and leaves a soft, silky, dry-touch finish without being greasy.

You'll likely see this ingredient in sunscreens because it does a nice job dissolving UV filters and keeping them evenly distributed.

Dicaprylyl Carbonate comes from carbonic acid and caprylyl alcohol, a fatty alcohol. It is an emollient and gives skin a velvet feel. The sources of Dicaprylyl Carbonate may be synthetic or from animals.

As an emollient, Dicaprylyl Carbonate creates a film on the skin. This film traps moisture in, keeping your skin soft and hydrated.

Diethylamino Hydroxybenzoyl Hexyl Benzoate (DHHB) is a chemical UV-A absorber. It is formulated for high UVA protection (320-400 nm).

DHHB is well-liked for:

Dipropylene Glycol is a synthetically created humectant, stabilizer, and solvent.

This ingredient helps:

Ethylhexyl Triazone (aka Octyl Triazone) is an oil-soluble organic UVB filter. It has peak absorption around 314 nm, right in the middle of the UVB range.

This ingredient is described as one of the most effective UVB filters available and small concentrations are enough to deliver a high SPF thanks to its strong UV absorbing power.

Ethylhexylglycerin is created from glycerin. It is a multitasker ingredient that:

The CIR Expert Panel found minimal skin absorption or sensitization of any kind in a safety assessment. Though this ingredient is considered well-tolerated, a small number of cases of allergic dermatitis have been published since 2002. Just be sure to patch test if you are unsure.

Lauryl Polyglyceryl-3 Polydimethylsiloxyethyl Dimethicone is a type of silicone.

Ozokerite is a naturally occuring mineral wax. In cosmetics, ozokerite is used as a texture enhancer.

Ceresin wax is derived from this ingredient.

This ingredient is a water-in-oil emulsifier and is sometimes known by its trade name, Isolan GPS. It helps create stable emulsions by bridging oil and water phases without adding a greasy feel.

Common usage levels sit between 2-5% for this ingredient.

Chances are, you eat sodium chloride every day. Sodium Chloride is also known as table salt. This ingredient has many purposes in skincare: thickener, emulsifier, and exfoliator.

You'll most likely find this ingredient in cleansers where it is used to create a gel-like texture. As an emulsifier, it also prevents ingredients from separating.

Synthetic Wax is a manufactured hydrocarbon wax. In formulas, it works as an occlusive emollient that helps reduce water loss and improves the spreadability of products.

Research comparing synthetic wax to traditional mineral-derived products found that formulas containing it perform as well for skin hydration.

This ingredient is used in makeup and skincare to thicken formulas, reduce shine, and give skin a silky-smooth feel.

It’s a white silicone powder that sits in fine lines and pores to blur their appearance though its effectiveness depends on the particle size.

Water. It's the most common cosmetic ingredient of all. You'll usually see it at the top of ingredient lists, meaning that it makes up the largest part of the product.

So why is it so popular? Water most often acts as a solvent - this means that it helps dissolve other ingredients into the formulation.