Npure Cica Beat the Sun SPF 50 PA++++ Versus Jayjun Cosmetic Okra Phyto Mucin Moisture Sun Gel SPF 50+

Because it is not a free-fatty acid, this ingredient is fungal acne safe (there's nothing for Malassezia to feed on).

This ingredient has been found to be safe as used in cosmetics, wasn't a skin or eye irritant in clinical patch testing, and wasn't phototoxic.

In a clinical comedogenicity test, this ingredient tested negative so it isn't likely to clog pores.

Typical use levels are about 5-8% for sunscreens + nail products, but can range from 0.005%-8% depending on the product.

DHHB has been approved by the EU, Japan, Taiwan, and South America for use up to 10%. Unfortunately, it has not been approved for use in the US or Canada due to slow regulatory processes.

This ingredient is soluble in oils, fats, and lipids.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

In vitro work measuring its UV-protective efficacy and photostability among 18 EU-approved filters and a peer-review of cosmetic UV filters confirms it performs best as a UVB booster rather than a standalone sunscreen.

Typical use levels sit at or below the EU regulatory cap of 10%, and it usually runs anywhere from 2-10% depending on the target SPF.

This ingredient is approved across the EU, UK, Australia, China, India, and Asia but has not been cleared in the US or Canada yet. This is more of a regulatory backlog situation and not a safety red flag.

A 2007 study measured the in-vitro SPF of 18 filters and found Polysilicone-15 contributed an SPF of about 3.64 at its maximum legal concentration (though worth noting its maker points out that in-vitro tests tend to underestimate its real performance because of its large polymeric structure).

Usage levels vary; it's approved up to 10% as a UV filter in the EU, China, Japan, Australia, ASEAN, and Mercosur countries. In the US, it's only permitted up to 1% as a light stabilizer because the FDA hasn't reviewed it as a sunscreen active.

Typical use levels range from 1-3%.

The EU's scientific committee concluded that this ingredient is safe for use as a UV absorber up to 10%, and tests came back negative for irritation, phototoxicity, and photoallergy.

There is one case of allergic lip inflammation from a lip balm with this ingredient, though this is rare.

This matters a lot because a lot of actives (like vitamin C) needs a specific pH to work well and feel comfortable on skin.

Concentration use ranges from 0.1-1.0% depending on the formula.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!