Vichy Capital Soleil Cell Protect Water Fluid Spray SPF 50+ Versus La Roche-Posay Anthelios UV Mune 400 Dermo-Pediatrics Invisible Spray SPF 50+

Because it is not a free-fatty acid, this ingredient is fungal acne safe (there's nothing for Malassezia to feed on).

Dicaprylyl Ether gives a non-greasy feel and better spreadability to products.

Emollients help hydrate the skin by creating a thin barrier. This thin barrier prevents moisture from escaping.

The standout trait is photostability. Unlike other UV filters, this one doesn't break down when exposed to sunlight.

You'll likely see it paired with Mexoryl SX (Ecamsule) because the two filters show a synergistic effect where the combined protection is greater than the sum of the individual filters.

Because it is oil soluble, it's great for water-resistant/sport/beach sunscreens.

Concentration-wise, the EU permits up to 15% but formulas use it well below that ceiling and almost never as a solo active.

It has a pretty solid safety record: allergic reactions are considered rare, its large molecule size means little to no absorption through skin, and toxicology reviews found no significant toxicity.

Just so you know, there were a handful of isolated allergic contact dermatitis case reports (which is true of every UV filter), but most people will not react to it.

This ingredient is available in the EU, Canada, Australia, and Japan, but not the US. This is just because the manufacturer hasn't pushed the data through the FDA's OTC ingredient pathway.

You'll often see it paired with other UV filters to boost overall SPF because octisalate is a fairly week filter on its own.

The reason you'll see it so often is because it can help solubilize and stabilize the trickier filters like oxybenzone and avobenzone.

Unlike these filters, octisalate has pretty good photostability and doesn't create skin-damaging free radicals when exposed to sunlight.

The fatty-alcohol part of the molecule also gives it a light, emollient feel so it doubles as a nice texture enhancer.

Usage levels vary around the world:

Safety-wise, this ingredient has a pretty reassuring track record. The EU's Scientific Committee on Consumer Products (SCCP) found very low skin penetration in human skin tests and negative results for irritation, phototoxicity, and photoallergy.

The real-world allergy risk is pretty low too; a 2012 European study of 1,031 people recorded only 2 reactions to it (a rate of 0.19%).

You might have seen scary headlines about sunscreen getting into your blood.

In 2019, the FDA found that several chemical filters can absorb through the skin and show up in the bloodstream at small but measurable levels.

Here's the important part: these tiny levels are just a cutoff the FDA uses to decide which ingredients need more testing and doesn't mean anything harmful was found.

The researchers were clear that the results are no reason to stop wearing sunscreen.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

Propanediol is not likely to cause sensitivity and considered safe to use. It is derived from corn or petroleum with a clear color and no scent.

Topically applied tocopherol has been shown to protect against UV damage by ramping up the skin's own natural defense enzymes.

It also acts as a skin conditioning agent; some studies show that regular topical use can improve the skin's water-binding capacity over 2-4 weeks.

This ingredient is especially loved for being a team player. When combined with Vitamin C, the photoprotective effect of both ingredients roughly doubles and the combo also helps reduce UV-induced DNA damage.

This ingredient has some brightening potential but it's more of a prevention ingredient than spot-fader. Cell studies show it can slow down melanin production but it's worth noting that it's not the most powerful brightener out there.

In formulations, it also serves as a stabilizer that helps protect other oxidation-prone ingredients from degrading.

Concentrations usually range from 0.1-1% in most leave-on products.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!