ISDIN Fotoprotector Pediatrics Transparent Spray SPF 50 Versus ISDIN Fotoprotector Transparent Spray Wet Skin SPF 50

Two of its biggest selling points are efficiency and stability:

Most of the other chemical filters are considered "photostable" if they can last for two hours.

Because this ingredient is oil-loving, it can sit neatly into the oil phase of emulsions and shines in water-repellent/water-resistant formulations.

The EU and Canada allow it to be used up to 10% and Japan allows it up to 5%.

Unfortunately, it's not yet an FDA approved sunscreen agent so you won't be able to find it in sunscreens in the US.

Safety-wise, it has a pretty solid record: the EU's Scientific Committee on Consumer Safety (SCCS) has reviewed it and found low skin absorption, no capacity to produce skin irritation or photo-irritation.

In vitro testing has found less than 0.1% of the applied dose is absorbed by the skin over 24 hours (mostly due to its large molecule size).

Fun fact: This ingredient even has anti-inflammatory properties similar to those of ketoprofe, an anti-inflammatory medication.

You'll often see it paired with other UV filters to boost overall SPF because octisalate is a fairly week filter on its own.

The reason you'll see it so often is because it can help solubilize and stabilize the trickier filters like oxybenzone and avobenzone.

Unlike these filters, octisalate has pretty good photostability and doesn't create skin-damaging free radicals when exposed to sunlight.

The fatty-alcohol part of the molecule also gives it a light, emollient feel so it doubles as a nice texture enhancer.

Usage levels vary around the world:

Safety-wise, this ingredient has a pretty reassuring track record. The EU's Scientific Committee on Consumer Products (SCCP) found very low skin penetration in human skin tests and negative results for irritation, phototoxicity, and photoallergy.

The real-world allergy risk is pretty low too; a 2012 European study of 1,031 people recorded only 2 reactions to it (a rate of 0.19%).

You might have seen scary headlines about sunscreen getting into your blood.

In 2019, the FDA found that several chemical filters can absorb through the skin and show up in the bloodstream at small but measurable levels.

Here's the important part: these tiny levels are just a cutoff the FDA uses to decide which ingredients need more testing and doesn't mean anything harmful was found.

The researchers were clear that the results are no reason to stop wearing sunscreen.

Formulators love it for its stability; its ability to filter UV stays practically unchanged even under intense radiation and it can also help boost the photostability of less stable filters like avobenzone.

It's also a great pick for water resistant products because it's insoluble in water and has a good affinity for keratin.

Because it's a big, heavy molecule, the European Scientific Committee has found to to have very low dermal penetration and negative results for allergenicity.

In vitro testing also showed a low absorption rate and clean results on irritation.

Typical use levels are 1-5% with 5% being the maximum in the EU, Japan, and other markets that allow it. However, this ingredient is not approved yet in the US or Canada.

If it does somehow make it onto your skin, it is chemically inert and does not penetrate or get absorbed into skin. Safety assessments note that adverse skin reactions to this ingredient are uncommon.

As an antioxidant, it helps fight free-radical molecules. Free-radical molecules are capable of damaging our cells and other genetic material. Thus, antioxidants may reduce the signs of aging.

This ingredient is oil-soluble.

Topically applied tocopherol has been shown to protect against UV damage by ramping up the skin's own natural defense enzymes.

It also acts as a skin conditioning agent; some studies show that regular topical use can improve the skin's water-binding capacity over 2-4 weeks.

This ingredient is especially loved for being a team player. When combined with Vitamin C, the photoprotective effect of both ingredients roughly doubles and the combo also helps reduce UV-induced DNA damage.

This ingredient has some brightening potential but it's more of a prevention ingredient than spot-fader. Cell studies show it can slow down melanin production but it's worth noting that it's not the most powerful brightener out there.

In formulations, it also serves as a stabilizer that helps protect other oxidation-prone ingredients from degrading.

Concentrations usually range from 0.1-1% in most leave-on products.

It's actually inactive on its own and works like a slow-release "storage" form; the enzymes in your skin called esterases gradually convert it into active vitamin E over time.

One in vivo study showed 5% of the acetate in the living layer of the epidermis converted to vitamin E after 5 days of application. This study also found the skin gained protection against UV damage even though the conversion was slow and small.

Once converted, vitamin E acts as a skin's main fat-soluble antioxidant that fights free radicals to protect skin from damage.

Topical vitamin E generally boosts the skin's photoprotection, and it reduced UV-damage in animal models.

This ingredient has some brightening potential but it's more of a prevention ingredient than spot-fader. Cell studies show it can slow down melanin production but it's worth noting that it's not the most powerful brightener out there.

Overall, it has a pretty solid safety profile and has been found to be non-irritating and non-comedogenic. Allergic reactions may happen but stay rare due to how widely the ingredient gets used.

The concentration will vary depending on the formula; industry data shows 0.1% in baby lotions, 3% in lipsticks, and 5% in foot powders. You can also find this ingredient at 100% in a pure vitamin E oil.

Most leave-on skincare keeps it at the lower end, often between 0.5-1%.

You'll also recognize water as that liquid we all need to stay alive. If you see this, drink a glass of water. Remember to stay hydrated!