Ami Colé Skin-Enhancing Tint

Dimethicone comes in different viscosities:

Depending on the viscosity, dimethicone has different properties.

Ingredients lists don't always show which type is used, so we recommend reaching out to the brand if you have questions about the viscosity.

This ingredient is unlikely to cause irritation because it does not get absorbed into skin. However, people with silicone allergies should be careful about using this ingredient.

Note: Dimethicone may contribute to pilling. This is because it is not oil or water soluble, so pilling may occur when layered with products. When mixed with heavy oils in a formula, the outcome is also quite greasy.

This ingredient may not be fungal-acne safe.

The comedogenic rating of this ingredient depends on the concentration. Lower amounts results in a lower rating.

Isopropyl Myristate may not be fungal acne safe. It can potentially worsen acne prone skin.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

Propanediol is not likely to cause sensitivity and considered safe to use. It is derived from corn or petroleum with a clear color and no scent.

Pumpkin seeds also contain fruit enzymes that act as an AHA. AHAs help exfoliate your skin, clean out pores, and increase cell turnover.

Fun fact: This ingredient comes from the field pumpkin, including winter squash and the traditional orange pumpkin we see in Autumn. Pumpkins were first domesticated in Southern Mexico about 10,000 years ago.

In cosmetics, Magnesium Sulfate is used to thicken a product or help dilute other solids. It is a non-reactive and non-irritating ingredient.

One study shows magnesium deficiency may lead to inflammation of the skin. Applying magnesium topically may help reduce inflammation.

You can find this ingredient in sea water or mineral deposits.

Industry-reported use ranges from 8% in rinse-off products and 2% in leave-on formulations.

This ingredient is an emollient, emulsifier, and penetration enhancer. As an emollient, it helps soften and hydrate skin by trapping moisture within. As an emulsifier, it prevents oil and water ingredients from separating.

Hydrogenated Lecithin can form tiny spherical structures made of phospholipid bilayers called liposomes. These liposomes are able to capture compounds inside their structure and deliver them through the skin barrier.

Because phospholipids are a natural component of our cell membranes, this ingredient is inherently compatible with skin.

A 2021 study found lecithin-based surfactants were less harsh and more tolerable comared to Sodium Lauryl Sulfate (SLS).

As a polysaccharide, Maltodextrin has moisturizing properties. Polysaccharides are a type of carbohydrate. The top layer of skin uses polysaccharides to retain water, keeping the skin hydrated.

Maltodextrin is water soluble and has a sweet taste.

Another benefit is a bit of UV protection. Vitamin E helps reduce the damage caused by UVB rays. (It should not replace your sunscreen). Combining it with Vitamin C can decrease sunburned cells and hyperpigmentation after UV exposure.

You might have noticed Vitamin E + C often paired together. This is because it is great at stabilizing Vitamin C. Using the two together helps increase the effectiveness of both ingredients.

There are often claims that Vitamin E can reduce/prevent scarring, but these claims haven't been confirmed by scientific research.

You might see people debate whether Sodium Chloride is comedogenic, but there actually haven't been any comedogenic tests done on it. Either way, the overall formulation of a product matters a lot more than any single ingredient.

You might see this ingredient used in scrubs as a primary exfoliating ingredient.

Sodium benzoate works as a preservative by inhibiting the growth of bacteria inside of cells. It prevents the cell from fermenting a type of sugar using an enzyme called phosphofructokinase.

It is the salt of benzoic acid. Foods containing sodium benzoate include soda, salad dressings, condiments, fruit juices, wines, and snack foods.

Studies for using ascorbic acid and sodium benzoate in cosmetics are lacking, especially in skincare routines with multiple steps.

We always recommend speaking with a professional, such as a dermatologist, if you have any concerns.

A 2021 paper looked at skincare formulations containing iron oxides and found that they reduced transmission of blue light when measured optically. In simple terms, the pigment particles helped block or scatter part of the visible light spectrum in lab testing and the authors suggest this could translate into better protection against blue-light-related skin effects.

There is also clinical and experimental research showing that tinted products containing iron oxides can reduce visible light-induced pigmentation:

Please note, whether a product reduces visible or blue light depends on things like:

In the EU's CosIng database, iron oxides are only listed as a colorant. CosIng groups ingredients by their main cosmetic role, such as colorant, preservative, or UV filter.

Though studies say iron oxides can "attenuate blue light", they're describing an optical property and not an officially recognized cosmetic function.

So CosIng isn’t contradicting the research. It’s just classifying iron oxides by what they officially are: pigments that add color.

Ci 77891 is commonly found in sunscreens due to its ability to block UV rays.