Revlon Colorstay Full Coverage Concealer

Dimethicone comes in different viscosities:

Depending on the viscosity, dimethicone has different properties.

Ingredients lists don't always show which type is used, so we recommend reaching out to the brand if you have questions about the viscosity.

This ingredient is unlikely to cause irritation because it does not get absorbed into skin. However, people with silicone allergies should be careful about using this ingredient.

Note: Dimethicone may contribute to pilling. This is because it is not oil or water soluble, so pilling may occur when layered with products. When mixed with heavy oils in a formula, the outcome is also quite greasy.

Isododecane's role as a solvent makes it a great texture enhancer. It spreads smoothly on skin and does not leave a sticky feeling behind. Isododecane also helps prevent color transfer in makeup products.

Isododecane is not absorbed into skin.

The chemical name for this ingredient is 2,2,4,6,6-PENTAMETHYLHEPTANE.

Your skin makes glycerin on its own (mostly from sebaceous oil breakdown) and shuttles it to your outermost layer of skin, or your epidermis, via aquaporin-3.

Aquaporin-3 is a transporter that is essential for normal skin hydration, elasticity, and repair. Interestingly, mice lacking in AQP3 have dry and less elastic skin that can be fully corrected with glycerin.

This ingredient is non-irritating, plays well with almost every ingredient, and works across all skin types. Typical use is anywhere between 3-10% but can go up to 79% in some leave-on products.

Just know very high concentrations (>40%) can feel tacky in low humidity.

Glycerin is the name for this ingredient in American English. British English uses Glycerol/Glycerine.

According to a manufacturer, it can blend seamlessly with silicone oils, such as Cyclopentasiloxane.

The unique structure of silica enhances the spreadability and adds smoothness, making it a great texture enhancer.

It is also used as an active carrier, emulsifier, and mattifier due to its ability to absorb excess oil.

In some products, tiny microneedles called spicules are made from silica or hydrolyzed sponge. When you rub them in, they lightly polish away dead skin layers and enhance the penetration of active ingredients.

PMMA is also able to enhance the texture of products by add a smooth feel.

You might see people debate whether Sodium Chloride is comedogenic, but there actually haven't been any comedogenic tests done on it. Either way, the overall formulation of a product matters a lot more than any single ingredient.

You might see this ingredient used in scrubs as a primary exfoliating ingredient.

There are a very small number of reported cases of contact dermatitis in cases linked to wound-care creams used over compromised skin (rather than skincare).

Overall, this is a well-studied and low-risk preservative just doing its job.

Typical concentrations run up to 0.6%, which is also the maximum amount permitted under both EU CosIng regulations and US FDA guidelines.

On top of that, this ingredient can counteract the effects of hard water by binding to the minerals in it.

One thing worth knowing is that Disodium EDTA has been shown to be a mild penetration enhancer. It can help other ingredients absorb into skin more effectively which can be a double-edged sword (great for actives, but can also make the active too strong if you have sensitive skin).

Clinical patch testing showed no significant skin irritation at typical use concentrations and minimal dermal absorption.

You'll most likely see this ingredient near the end of an ingredient list. It's typically found in concentrations less than 1%.

Because it is not a free-fatty acid, this ingredient is fungal acne safe (there's nothing for Malassezia to feed on).

As a preservative, it is used to stabilize products and prevent them from degrading. Specifically, BHT prevents degradation from oxidation.

The concerns related to BHT come from oral studies; this ingredient is currently allowed for use by both the FDA and EU.

However, it was recently restricted for use in the UK as of April 2024.

A 2021 paper looked at skincare formulations containing iron oxides and found that they reduced transmission of blue light when measured optically. In simple terms, the pigment particles helped block or scatter part of the visible light spectrum in lab testing and the authors suggest this could translate into better protection against blue-light-related skin effects.

There is also clinical and experimental research showing that tinted products containing iron oxides can reduce visible light-induced pigmentation:

Please note, whether a product reduces visible or blue light depends on things like:

In the EU's CosIng database, iron oxides are only listed as a colorant. CosIng groups ingredients by their main cosmetic role, such as colorant, preservative, or UV filter.

Though studies say iron oxides can "attenuate blue light", they're describing an optical property and not an officially recognized cosmetic function.

So CosIng isn’t contradicting the research. It’s just classifying iron oxides by what they officially are: pigments that add color.

Ci 77891 is commonly found in sunscreens due to its ability to block UV rays.

This ingredient is often coated with metal oxides like titanium dioxide. Trace amounts of heavy metals may be found in mica, but these metals are not harmful in our personal products.

Mica has been used since prehistoric times throughout the world. Ancient Egyptian, Indian, Greek, Roman, Aztec, and Chinese civilizations have used mica.

Interestingly, the size of the molecule affects its behavior:

Some clinical evidence links low molecular weight versions to improved wrinkle depth, elasticity, anti-inflammatory effects, and barrier repair.

Many serums use a blend of both weights so you can get surface hydration plus longer-lasting and deeper effects.

You'll typically see concentrations between 0.1-2% for this ingredient.

Tocopheryl Acetate is commonly found in both skincare and dietary supplements.

According to in-vivo and ex-vivo studies done by a manufacturer, this ingredient works well with UV filters:

Industry-reported use ranges from 8% in rinse-off products and 2% in leave-on formulations.