Barry M Cosmetics Lid Lock - Eyeshadow Primer

This ingredient may not be fungal acne safe because behenic acid falls into the chain-length range that Malassezia yeasts can feed on.

Studies found this ingredient did not irritate skin in concentrations below 15%.

It is considered non-irritating on the skin.

Polymethylsilsesquioxane has not been shown to clog pores. It has been deemed safe to use up to 55%, but most cosmetics use much less.

If you have concerns about using this ingredient, we recommend speaking with a professional.

According to a manufacturer, it can blend seamlessly with silicone oils, such as Cyclopentasiloxane.

On a cellular level, it disrupts the cell membranes of microbes by poking holes that make the cell leak. This shuts down the chemical reactions the microbe needs to make energy so it can no longer survive.

Another perk of this ingredient is that it stays functional across a wide pH range (3-10).

You'll often see it paired with boosters like Ethylhexylglycerin; one study showed that a 1:9 ratio of Ethylhexylglycerin to Phenoxyethanol damages bacterial membranes as effectively as doubling the Phenoxyethanol concentration on its own.

Typical use concentrations range from 0.3-1% depending on the formula, and this ingredient is capped at 1% int the EU.

Safety-wise, the fear mongering does not hold up to the evidence. The EU's Scientific Committee on Consumer Safety and FDA consider it safe as a preservative at up to 1%, including for children of all ages.

Adverse systemic effects only showed up in animal studies at exposures roughly 200x higher than what people get from cosmetics. And despite its very widespread use, this ingredient is a rare sensitizer and allergic reactions are uncommon.

It's actually inactive on its own and works like a slow-release "storage" form; the enzymes in your skin called esterases gradually convert it into active vitamin E over time.

One in vivo study showed 5% of the acetate in the living layer of the epidermis converted to vitamin E after 5 days of application. This study also found the skin gained protection against UV damage even though the conversion was slow and small.

Once converted, vitamin E acts as a skin's main fat-soluble antioxidant that fights free radicals to protect skin from damage.

Topical vitamin E generally boosts the skin's photoprotection, and it reduced UV-damage in animal models.

This ingredient has some brightening potential but it's more of a prevention ingredient than spot-fader. Cell studies show it can slow down melanin production but it's worth noting that it's not the most powerful brightener out there.

Overall, it has a pretty solid safety profile and has been found to be non-irritating and non-comedogenic. Allergic reactions may happen but stay rare due to how widely the ingredient gets used.

The concentration will vary depending on the formula; industry data shows 0.1% in baby lotions, 3% in lipsticks, and 5% in foot powders. You can also find this ingredient at 100% in a pure vitamin E oil.

Most leave-on skincare keeps it at the lower end, often between 0.5-1%.

Studies show this ingredient to be safe for cosmetics. When it is undiluted, it can cause skin irritation. (It is always diluted in skincare and makeup). This ingredient is water-soluble.

Propylene Carbonate is created from propylene glycol and carbonic acid.

Synthetically created Ci 77491 is considered safer than those naturally found. This is because the synthetically created version may contain less impurities. Iron oxides are generally non-toxic and non-allergenic.

The unique structure of silica enhances the spreadability and adds smoothness, making it a great texture enhancer.

It is also used as an active carrier, emulsifier, and mattifier due to its ability to absorb excess oil.

In some products, tiny microneedles called spicules are made from silica or hydrolyzed sponge. When you rub them in, they lightly polish away dead skin layers and enhance the penetration of active ingredients.

Ci 77891 is commonly found in sunscreens due to its ability to block UV rays.

Industry-reported use ranges from 8% in rinse-off products and 2% in leave-on formulations.